realtek 8139

Zulik · 23 Czerwca 2003

witam !

mam sieciowke na plycie ale co tam :) postanowilem wlozyc sobie jeszcze jedną na chipsecie RTL8139 w celu oczywiscie przetestowania ich wspolnej pracy.

Pytania:

czy jesli RTL8139 jest na eth0 - to moja sieciowka na plycie powinna sie odezwac na eth1 ??!! .....a ona nic :( wpisalem ifconfig eth1 i gucio :(

z tym ze nie mialem przewodu sieciowego podpietego pod sieciowke na plycie - moze to przez to !

2:

czym rozni sie 8139too od 8139cp - Linux probuje ladowac oba :(( a tylko 8139too jest dobry ! a przy 8139cp zglasza mi ze nie to przerwanie i wogole !

no ale po co kurde wda moduly od sieciowki ??

a nigdzie nie mam wpisu z tym pieprzonym 8139cp !!!! nie wiem jakim cudem to mi sie laduje ;(

ParanoiK · 23 Czerwca 2003

1) Co ci ifconfig wypisuje? Co ty dokładnie wpisałeś? Jaka dystrybucja?

2) Trochę inne chipsety

Zulik · 24 Czerwca 2003

w skrocie to powiem tak

zalozmy ze mam tylko jedna sieciowke w kompie

i mi sie robilo tak ze do niej 2 moduly instalowaly !! z tego jeden bledny !

wystarczylo wpis zrobic w module.conf alias 8139cp off i juz :)

a sieciowka laduje mi sie przez 8139too

ParanoiK · 24 Czerwca 2003

No i prawidłowo ;> Działa wszystko? ;]

Zulik · 24 Czerwca 2003

a jak :D chula az milo :)

z tym ze nie wiem czy to wina karty czy moze mojego systemu ?!

macie jakies opinie na ten temat ?

ParanoiK · 24 Czerwca 2003

Prawdopodobnie moduły się w jakiś sposób pożarły. Jakie masz distro?

Zulik · 24 Czerwca 2003

nooo najlepsze :D

slackware 9 :)

ParanoiK · 25 Czerwca 2003

Zobacz czy nie masz jakiegoś bajzlu w /etc/rc.d/rc.modules

Zulik · 25 Czerwca 2003

oto moj dmesg:

Linux version 2.4.20 (root@midas) (gcc version 3.2.2) #2 Mon Mar 17 22:02:15 PST 2003

BIOS-provided physical RAM map:

BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)

BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)

BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)

BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)

BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)

BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)

BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)

BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)

511MB LOWMEM available.

On node 0 totalpages: 131056

zone(0): 4096 pages.

zone(1): 126960 pages.

zone(2): 0 pages.

Kernel command line: BOOT_IMAGE=Linux ro root=301

Initializing CPU#0

Detected 2004.561 MHz processor.

Console: colour VGA+ 80x25

Calibrating delay loop... 3997.69 BogoMIPS

Memory: 515504k/524224k available (1733k kernel code, 8336k reserved, 568k data, 112k init, 0k highmem)

Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)

Inode cache hash table entries: 32768 (order: 6, 262144 bytes)

Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)

Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)

Page-cache hash table entries: 131072 (order: 7, 524288 bytes)

CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)

CPU: L2 Cache: 256K (64 bytes/line)

CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000

CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000

CPU: AMD Athlon XP 2400+ stepping 01

Enabling fast FPU save and restore... done.

Enabling unmasked SIMD FPU exception support... done.

Checking 'hlt' instruction... OK.

POSIX conformance testing by UNIFIX

mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)

mtrr: detected mtrr type: Intel

PCI: PCI BIOS revision 2.10 entry at 0xfb4f0, last bus=2

PCI: Using configuration type 1

PCI: Probing PCI hardware

PCI: Discovered primary peer bus ff [iRQ]

PCI: Using IRQ router default [10de/01e0] at 00:00.0

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

VFS: Diskquotas version dquot_6.4.0 initialized

Journalled Block Device driver loaded

Detected PS/2 Mouse Port.

pty: 512 Unix98 ptys configured

Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled

Real Time Clock Driver v1.10e

Uniform Multi-Platform E-IDE driver Revision: 6.31

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

PCI_IDE: unknown IDE controller on PCI bus 00 device 48, VID=10de, DID=0065

PCI_IDE: chipset revision 162

PCI_IDE: not 100% native mode: will probe irqs later

ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA

ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA

hda: SAMSUNG SP2002H, ATA DISK drive

hdb: WDC WD800JB-00CRA1, ATA DISK drive

hdc: LITE-ON LTR-48125W, ATAPI CD/DVD-ROM drive

ide0 at 0x1f0-0x1f7,0x3f6 on irq 14

ide1 at 0x170-0x177,0x376 on irq 15

hda: 39180960 sectors (20061 MB) w/1962KiB Cache, CHS=2438/255/63

hdb: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=9729/255/63

hdc: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)

Uniform CD-ROM driver Revision: 3.12

ide-floppy driver 0.99.newide

Partition check:

hda: hda1 hda2 hda3 hda4

hdb: hdb1 hdb2 < hdb5 >

Floppy drive(s): fd0 is 1.44M

FDC 0 is a post-1991 82077

RAMDISK driver initialized: 16 RAM disks of 7777K size 1024 blocksize

loop: loaded (max 8 devices)

ide-floppy driver 0.99.newide

SCSI subsystem driver Revision: 1.00

kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2

md: linear personality registered as nr 1

md: raid0 personality registered as nr 2

md: raid1 personality registered as nr 3

md: raid5 personality registered as nr 4

raid5: measuring checksumming speed

8regs : 2874.400 MB/sec

32regs : 1652.800 MB/sec

pIII_sse : 5511.600 MB/sec

pII_mmx : 4694.400 MB/sec

p5_mmx : 5989.600 MB/sec

raid5: using function: pIII_sse (5511.600 MB/sec)

md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27

md: Autodetecting RAID arrays.

md: autorun ...

md: ... autorun DONE.

LVM version 1.0.5+(22/07/2002)

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP

IP: routing cache hash table of 4096 buckets, 32Kbytes

TCP: Hash tables configured (established 32768 bind 65536)

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

VFS: Mounted root (ext2 filesystem) readonly.

Freeing unused kernel memory: 112k freed

Adding Swap: 546200k swap-space (priority -1)

PCI: Setting latency timer of device 00:04.0 to 64

8139too Fast Ethernet driver 0.9.26

eth1: RealTek RTL8139 Fast Ethernet at 0xe0862000, 00:00:1c:d3:0c:e0, IRQ 12

eth1: Identified 8139 chip type 'RTL-8139C'

btaudio: driver version 0.7 loaded [digital+analog]

btaudio: Bt878 (rev 17) at 01:09.1, irq: 5, latency: 32, mmio: 0xdc001000

btaudio: using card config "default"

btaudio: registered device dsp0 [digital]

btaudio: registered device dsp1 [analog]

btaudio: registered device mixer0

Linux video capture interface: v1.00

i2c-core.o: i2c core module

i2c-algo-bit.o: i2c bit algorithm module

bttv: driver version 0.7.96 loaded

bttv: using 4 buffers with 2080k (8320k total) for capture

bttv: Host bridge is PCI device 10de:01e0 (nVidia Corporation)

bttv: Bt8xx card found (0).

bttv0: Bt878 (rev 17) at 01:09.0, irq: 5, latency: 32, mmio: 0xdc000000

bttv0: using: BT878( *** UNKNOWN/GENERIC **) [card=0,autodetected]

i2c-core.o: adapter bt848 #0 registered as adapter 0.

bttv0: using tuner=-1

bttv0: i2c: checking for MSP34xx @ 0x80... not found

bttv0: i2c: checking for TDA9875 @ 0xb0... found

i2c-core.o: driver i2c tda9875 driver registered.

tda9875: no such chip at 0xb0 (dic=0x11 rev=0x2)

bttv0: i2c: checking for TDA7432 @ 0x8a... not found

i2c-core.o: driver i2c TV tuner driver registered.

tuner: probing bt848 #0 i2c adapter [id=0x10005]

tuner: chip found @ 0xc2

bttv0: i2c attach [client=(unset),ok]

i2c-core.o: client [(unset)] registered to adapter [bt848 #0](pos. 0).

bttv0: registered device video0

bttv0: registered device vbi0

Intel 810 + AC97 Audio, version 0.21, 15:37:49 Mar 11 2003

PCI: Setting latency timer of device 00:06.0 to 64

i810: NVIDIA nForce Audio found at IO 0xd800 and 0xd400, IRQ 7

i810_audio: Audio Controller supports 6 channels.

ac97_codec: AC97 Audio codec, id: 0x414c:0x4720 (Unknown)

i810_audio: AC'97 codec 0, new EID value = 0x05c7

i810_audio: AC'97 codec 0, DAC map configured, total channels = 6

usb.c: registered new driver usbdevfs

usb.c: registered new driver hub

PCI: Setting latency timer of device 00:02.2 to 64

hcd.c: ehci-hcd @ 00:02.2, PCI device 10de:0068 (nVidia Corporation)

hcd.c: irq 4, pci mem e08c2000

usb.c: new USB bus registered, assigned bus number 1

ehci-hcd.c: USB 2.0 support enabled, EHCI rev 1. 0

hub.c: USB hub found

hub.c: 6 ports detected

PCI: Setting latency timer of device 00:02.0 to 64

usb-ohci.c: USB OHCI at membase 0xe08ca000, IRQ 12

usb-ohci.c: usb-00:02.0, PCI device 10de:0067 (nVidia Corporation)

usb.c: new USB bus registered, assigned bus number 2

hub.c: USB hub found

hub.c: 3 ports detected

PCI: Setting latency timer of device 00:02.1 to 64

usb-ohci.c: USB OHCI at membase 0xe08cc000, IRQ 11

usb-ohci.c: usb-00:02.1, PCI device 10de:0067 (nVidia Corporation)

usb.c: new USB bus registered, assigned bus number 3

hub.c: USB hub found

hub.c: 3 ports detected

hub.c: new USB device 00:02.0-1, assigned address 2

usb.c: USB device 2 (vend/prod 0x46d/0xc025) is not claimed by any active driver.

usb-uhci.c: $Revision: 1.275 $ time 15:38:38 Mar 11 2003

usb-uhci.c: High bandwidth mode enabled

usb-uhci.c: v1.275:USB Universal Host Controller Interface driver

uhci.c: USB Universal Host Controller Interface driver v1.1

hub.c: new USB device 00:02.0-3, assigned address 3

usb.c: USB device 3 (vend/prod 0x8ca/0x10) is not claimed by any active driver.

usb.c: registered new driver usb_mouse

input0: B16_b_02 USB-PS/2 Optical Mouse on usb2:2.0

input1: AIPTEK International Inc. USB Tablet Series Version 1.04 on usb2:3.0

usbmouse.c: v1.6:USB HID Boot Protocol mouse driver

usb.c: registered new driver hiddev

usb.c: registered new driver hid

hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>

hid-core.c: USB HID support drivers

mice: PS/2 mouse device common for all mice

apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)

ISO 9660 Extensions: Microsoft Joliet Level 3

ISO 9660 Extensions: RRIP_1991A

8139cp: 10/100 PCI Ethernet driver v0.3.0 (Sep 29, 2002)

czemu az 4 sekcje 8139cp ?

teraz:

lspci

00:00.0 Host bridge: nVidia Corporation: Unknown device 01e0 (rev a2)

00:00.1 RAM memory: nVidia Corporation: Unknown device 01eb (rev a2)

00:00.2 RAM memory: nVidia Corporation: Unknown device 01ee (rev a2)

00:00.3 RAM memory: nVidia Corporation: Unknown device 01ed (rev a2)

00:00.4 RAM memory: nVidia Corporation: Unknown device 01ec (rev a2)

00:00.5 RAM memory: nVidia Corporation: Unknown device 01ef (rev a2)

00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a3)

00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)

00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller (rev a3)

00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller (rev a3)

00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller (rev a3)

00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet Controller (rev a1)

00:05.0 Multimedia audio controller: nVidia Corporation nForce MultiMedia audio [Via VT82C686B] (rev a2)

00:06.0 Multimedia audio controller: nVidia Corporation nForce2 AC97 Audio Controler (MCP) (rev a1)

00:08.0 PCI bridge: nVidia Corporation: Unknown device 006c (rev a3)

00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2)

00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev a2)

01:09.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)

01:09.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)

01:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)

02:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev b2)

proba zaladowania tego modulu po uwczesnym zachaszczowaniu linii alias 8139cp off - daje komunikat

root@zulik:~# lspci