sieciowka pcmcia irq

[w3rt]

dmesg:

 

Intel PCIC probe: not found.

Databook TCIC-2 PCMCIA probe: not found.

PCI: No IRQ known for interrupt pin A of device 00:13.0. Please try using pci=biosirq.

PCI: No IRQ known for interrupt pin B of device 00:13.1. Please try using pci=biosirq.

Yenta IRQ list 06b8, PCI irq0

Socket status: 30000020

Yenta IRQ list 0eb8, PCI irq0

Socket status: 30000007

cs: cb_alloc(bus 20): vendor 0x10ec, device 0x8139

PCI: Enabling device 14:00.0 (0000 -> 0003)

PCI: No IRQ known for interrupt pin A of device 14:00.0. Please try using pci=biosirq.

cs: IO port probe 0x0c00-0x0cff: clean.

cs: IO port probe 0x0800-0x08ff: clean.

cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x480-0x48f 0x4d0-0x4d7

cs: IO port probe 0x0a00-0x0aff: clean.

8139too Fast Ethernet driver 0.9.26

PCI: No IRQ known for interrupt pin A of device 14:00.0. Please try using pci=biosirq.

PCI: Setting latency timer of device 14:00.0 to 64

eth0: RealTek RTL8139 Fast Ethernet at 0xca84d000, 00:30:4f:22:85:62, IRQ 0

eth0: Identified 8139 chip type 'RTL-8139C'

 

i nie da sie podniesc eth0...

pci=biosirq? wpisalem to i...? nic

 

Pozdrawiam

[bigfan]

Trzeba to wpisac przy starcie systemu np. jako argument po nazwie obrazu jadra w lilo:

lilo: linux pci=biosirq

[w3rt]

Linux Kernel Card Services 3.1.22

options: [pci] [cardbus] [pm]

isapnp: Scanning for PnP cards...

isapnp: No Plug & Play device found

Intel PCIC probe: not found.

Databook TCIC-2 PCMCIA probe: not found.

PCI: No IRQ known for interrupt pin A of device 00:13.0.

PCI: No IRQ known for interrupt pin B of device 00:13.1.

Yenta IRQ list 0eb8, PCI irq0

Socket status: 30000020

Yenta IRQ list 0eb8, PCI irq0

Socket status: 30000007

cs: cb_alloc(bus 20): vendor 0x10ec, device 0x8139

PCI: Enabling device 14:00.0 (0000 -> 0003)

PCI: No IRQ known for interrupt pin A of device 14:00.0.

cs: IO port probe 0x0c00-0x0cff: clean.

cs: IO port probe 0x0800-0x08ff: clean.

cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x480-0x48f 0x4d0-0x4d7

cs: IO port probe 0x0a00-0x0aff: clean.

8139too Fast Ethernet driver 0.9.26

PCI: No IRQ known for interrupt pin A of device 14:00.0.

PCI: Setting latency timer of device 14:00.0 to 64

eth0: RealTek RTL8139 Fast Ethernet at 0xca939000, 00:30:4f:22:85:62, IRQ 0

eth0: Identified 8139 chip type 'RTL-8139C'

 

teraz pokazuje sie to bez pci=biosirq... Aha jeszcze jedno, pod windowsem wszystko ladnie dziala... a przy podnoszeniu interfejsu pokazuje sie: SIOCSIFFLAGS: Device or resource busy

[bigfan]

No a probowales z ta opcja bootowac system?

[w3rt]

no mowie... dodalem do lilo pci=biosirq i sie z tym bootuje.. i wyskakuje to wyrzej

[bigfan]

No jak dla mnie to napisales dokladnie odwrotnie wczesniej ;-) Masz jaderko z obsluga wszystkich kontrolerow PCMCIA? - jest taka sekcja, gdzie mozna je powybierac sobie, jak nie wiesz jaki to wybierasz wszystkie.

[w3rt]

Tak.. cale jaderko jest w porzadku ;)