Nec 20,5gb Zgłasza Problemy Po Nieudanym Partycjonowaniu(?)

[Lewiatan]

Czesc...

Ostatnio nabyłem dysk twardy neca na elektronice IBM. Winda była zainstalowana, dwie partycje... Zrobiłem format i zainstalowałem linuksa...(4 razy)... Po ostatnim dzieleniu dysku nie mogę zainstalować żadnego systemu na twardzielu. Oddałem dysk do informatyka, ten porobił jakieś testy(nic nie wiem na temat tychże) i zwrócił mi dysk ze słowami( tu cytuję...) "nic nie da się zrobić'...

 

Smart pokazuje mi cos takiego...

=== START OF INFORMATION SECTION ===

Device Model: IBM-DTLA-305020

Serial Number: YEEYET41483

Firmware Version: TW2OA60A

Device is: In smartctl database [for details use: -P show]

ATA Version is: 5

ATA Standard is: ATA/ATAPI-5 T13 1321D revision 1

Local Time is: Tue Mar 21 08:35:40 2006 CET

 

==> WARNING: IBM Deskstar 40GV and 75GXP drives may need upgraded SMART firmware.

Please see http://www.geocities.com/dtla_update/ and

http://www-3.ibm.com/pc/support/site.wss/d...ocid=MIGR-42215

 

SMART support is: Available - device has SMART capability.

SMART support is: Enabled

 

=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED

 

General SMART Values:

Offline data collection status: (0x80) Offline data collection activity

was never started.

Auto Offline Data Collection: Enabled.

Self-test execution status: ( 0) The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: (1559) seconds.

Offline data collection

capabilities: (0x1b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

No Conveyance Self-test supported.

No Selective Self-test supported.

SMART capabilities: (0x0003) Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability: (0x01) Error logging supported.

No General Purpose Logging support.

Short self-test routine

recommended polling time: ( 1) minutes.

Extended self-test routine

recommended polling time: ( 15) minutes.

 

SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE

1 Raw_Read_Error_Rate 0x000b 100 100 060 Pre-fail Always - 0

2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0

3 Spin_Up_Time 0x0007 110 110 024 Pre-fail Always - 114 (Average 121)

4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 1036

5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 12

7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0

8 Seek_Time_Performance 0x0005 100 100 020 Pre-fail Offline - 0

9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 3716

10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0

12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 981

192 Power-Off_Retract_Count 0x0032 100 100 050 Old_age Always - 1036

193 Load_Cycle_Count 0x0012 100 100 050 Old_age Always - 1036

194 Temperature_Celsius 0x0002 148 148 000 Old_age Always - 37

196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 17

197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0

198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0

199 UDMA_CRC_Error_Count 0x000a 200 253 000 Old_age Always - 0

 

SMART Error Log Version: 1

ATA Error Count: 309 (device log contains only the most recent five errors)

CR = Command Register [HEX]

FR = Features Register [HEX]

SC = Sector Count Register [HEX]

SN = Sector Number Register [HEX]

CL = Cylinder Low Register [HEX]

CH = Cylinder High Register [HEX]

DH = Device/Head Register [HEX]

DC = Device Command Register [HEX]

ER = Error register [HEX]

ST = Status register [HEX]

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.

 

Error 309 occurred at disk power-on lifetime: 3699 hours (154 days + 3 hours)

When the command that caused the error occurred, the device was active or idle.

 

After command completion occurred, registers were:

ER ST SC SN CL CH DH

-- -- -- -- -- -- --

40 59 08 88 45 11 e0 Error: UNC at LBA = 0x00114588 = 1131912

 

Commands leading to the command that caused the error were:

CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name

-- -- -- -- -- -- -- -- ---------------- --------------------

c4 b9 08 88 45 11 e0 00 02:04:45.500 READ MULTIPLE

c6 b9 10 00 00 00 e4 00 02:04:45.500 SET MULTIPLE MODE

91 b9 3f 00 00 00 af 00 02:04:45.500 INITIALIZE DEVICE PARAMETERS [OBS-6]

10 b9 00 00 00 00 a0 00 02:04:45.400 RECALIBRATE [OBS-4]

c4 b9 08 88 45 11 e0 00 02:04:39.600 READ MULTIPLE

 

Error 308 occurred at disk power-on lifetime: 3699 hours (154 days + 3 hours)

When the command that caused the error occurred, the device was active or idle.

 

After command completion occurred, registers were:

ER ST SC SN CL CH DH

-- -- -- -- -- -- --

40 59 08 88 45 11 e0 Error: UNC at LBA = 0x00114588 = 1131912

 

Commands leading to the command that caused the error were:

CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name

-- -- -- -- -- -- -- -- ---------------- --------------------

c4 b9 08 88 45 11 e0 00 02:04:39.600 READ MULTIPLE

c6 b9 10 00 00 00 e4 00 02:04:39.600 SET MULTIPLE MODE

91 b9 3f 00 00 00 af 00 02:04:39.600 INITIALIZE DEVICE PARAMETERS [OBS-6]

10 b9 00 00 00 00 a0 00 02:04:39.600 RECALIBRATE [OBS-4]

c4 b9 08 88 45 11 e0 00 02:04:33.700 READ MULTIPLE

 

Error 307 occurred at disk power-on lifetime: 3699 hours (154 days + 3 hours)

When the command that caused the error occurred, the device was active or idle.

 

After command completion occurred, registers were:

ER ST SC SN CL CH DH

-- -- -- -- -- -- --

40 59 08 88 45 11 e0 Error: UNC at LBA = 0x00114588 = 1131912

 

Commands leading to the command that caused the error were:

CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name

-- -- -- -- -- -- -- -- ---------------- --------------------

c4 b9 08 88 45 11 e0 00 02:04:33.700 READ MULTIPLE

c6 b9 10 00 00 00 e4 00 02:04:33.700 SET MULTIPLE MODE

91 b9 3f 00 00 00 af 00 02:04:33.700 INITIALIZE DEVICE PARAMETERS [OBS-6]

10 b9 00 00 00 00 a0 00 02:04:33.700 RECALIBRATE [OBS-4]

c4 b9 08 88 45 11 e0 00 02:04:27.800 READ MULTIPLE

 

Error 306 occurred at disk power-on lifetime: 3699 hours (154 days + 3 hours)

When the command that caused the error occurred, the device was active or idle.

 

After command completion occurred, registers were:

ER ST SC SN CL CH DH

-- -- -- -- -- -- --

40 59 08 88 45 11 e0 Error: UNC at LBA = 0x00114588 = 1131912

 

Commands leading to the command that caused the error were:

CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name

-- -- -- -- -- -- -- -- ---------------- --------------------

c4 b9 08 88 45 11 e0 00 02:04:27.800 READ MULTIPLE

c6 b9 10 00 00 00 e4 00 02:04:27.800 SET MULTIPLE MODE

91 b9 3f 00 00 00 af 00 02:04:27.800 INITIALIZE DEVICE PARAMETERS [OBS-6]

10 b9 00 00 00 00 a0 00 02:04:27.800 RECALIBRATE [OBS-4]

c4 b9 08 88 45 11 e0 00 02:04:21.900 READ MULTIPLE

 

Error 305 occurred at disk power-on lifetime: 3699 hours (154 days + 3 hours)

When the command that caused the error occurred, the device was active or idle.

 

After command completion occurred, registers were:

ER ST SC SN CL CH DH

-- -- -- -- -- -- --

40 59 08 88 45 11 e0 Error: UNC at LBA = 0x00114588 = 1131912

 

Commands leading to the command that caused the error were:

CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name

-- -- -- -- -- -- -- -- ---------------- --------------------

c4 b9 08 88 45 11 e0 00 02:04:21.900 READ MULTIPLE

c4 b9 08 80 45 11 e0 00 02:04:21.900 READ MULTIPLE

c4 b9 08 78 45 11 e0 00 02:04:21.900 READ MULTIPLE

c4 b9 08 70 45 11 e0 00 02:04:21.900 READ MULTIPLE

c4 b9 08 68 45 11 e0 00 02:04:21.900 READ MULTIPLE

 

SMART Self-test log structure revision number 1

No self-tests have been logged. [To run self-tests, use: smartctl -t]

 

 

Device does not support Selective Self Tests/Logging

------------

 

Czy ktoś może mi doradzić, co z nim mogę jeszcze zrobić? Obecnie pracuje na bootowalnym linuksie, ale to mnie zaczyna już powoli męczyć. Nie wiem, czy kupić nowy dysk, czy nad tym się męczyć...

 

Jako ciekawostkę mogę dodać, że spod dosa udało mi się wgrać na partycję plik readme.txt poprzez skopiowanie, ale już na [brzydkie określenie na linuksa]u nic nie mogłem zrobić...

 

Proszę o pomoc......;/

pozdro, lewiatan

 

---edit---

Czy jest szansa zainstalowania systemu na takim dysku?

Edytowane 21 Marca 2006 przez Lewiatan

[rosolini]

Odpal spod DOSa Partition Magica, usun wszystkie partycje i pozakladaj od nowa. Jezeli PM wyswietli caly dysk na zolto i bedzie pisal o jakims bledzie, to prawdopodobnie bedziesz musial przeprowadzic formatowanie niskopoziomowe, tzw. low level format. Mozna co prawda jeszcze sprobowac spod instalatora Win XP, ale raczej nie przyniesie to porzadanego rezultatu.

[Lewiatan]

dzięki za zainteresowanie rosolini....;) Chyba sobie to odpuszczę, bo jutro mam komputer wymieniany na inną jednostkę, taką samą, więc gra nie warta świeczki... Niech inni bawią się z tym.

 

Z tego, co zauwazyłem to jest na tym dysku czysta partycja, już zapewne po tych zabiegach... Jakby początkowe sektory były zrąbane...

 

Dzięki jeszcze raz...

[rosolini]

... i nie mozna wejcs na ta partycje spod windows, nie mozna nic na nia skopiowac... o dziwo daje sie ona sformatowac, mozna ja usunac, zalozyc na nowo, przeczesac chkdsk-iem ale to nic nie daje...

 

mialem ostatnio na warsztacie kilka takich przypadkow - nawet wczoraj jeden - i wszystkie dyski dalo sie naprawic

 

low level format czyni cuda ;) oczywiscie nalezy w tym celu stosowac firmowe oprogramowanie producenta dysku

Edytowane 22 Marca 2006 przez rosolini